HyConn Update – What Happened After Shark Tank

Mark Cuban has not publicly commented on the deal. Stroope’s newness to deal making with investors proves he lacks understanding of the due diligence process. Entrepreneurs learn this lesson through hard knocks. Stroope hints, Mark Cuban concluded licensing the design to another company is the best strategy to bring the quick-disconnect hose fitting to market. It would reduce the cost and increase the profit margin. Apparently, Jeff Stroope disliked Cuban’s new strategy, forcing entrepreneur and investor to part ways. Jeff Stroope would no longer be needed with a licensing deal, making the Mark Cuban deal less appealing. The deal does not end with Mark Cuban.

Cleaning, Jetting, Waterblasting and Maintenance

Water heaters are one of the most important components for providing comfort in homes. However, very often, they are located in difficult to access confined spaces or tight closets. All SharkBite water heater connectors are approved for use on electric or gas water heaters with a flu vent.

Mosmatic duct, manhole, and silo cleaners, surface cleaners, undercarriage cleaners, and replacement parts are all provided through Power Wash Store. Don’t see what you’re looking for? Give us a call for more information regarding your specific needs.

I didn’t know I’d have to write a description. How many words is that so far, like a hundred? Stuff that interests you. It’s in the name, ffs. Hover below for more info, and check out our wiki page! No memes This includes references in titles of your post e. No related posts Posts that acknowledge, “one-up,” or relate specifically to another post are not allowed e.

HOW TO: INSTALL A WATER HEATER WITH SHARKBITE

New tools for jetting, cable machine cleaning and industrial vacuum loading serve a variety of functions, from the cleaning of debris, roots and grease from various-sized pipe, to removing paint and other coatings from surfaces, to hydroexcavation and cutting. Here is a look at some of the latest developments. A rear-mounted volt electric jetter hose reel and SS rear stack-mounted manual pressure washer and garden hose reels provide ample hose space.

They come standard with feet of jetter hose, two nozzles, and a complete set of washdown accessories.

This innovative tank comes ready to install, complete with gph quality pump and all fittings. The polythene lid doubles as a cutting board. The tank is self flushing at boat speeds in excess of 10 knots.

He noticed something alarming — attaching the standard fire hose to a fire hydrant took up to 30 seconds, which is a lot of time during an emergency. He invented the HyConn connector, which takes 3 seconds or less. Would the Sharks bite on this potentially life-saving idea? He said that he was the creator of HyConn. Jeff stated that he was a full-time captain of the fire brigade, as well as a maintenance supervisor. The video showed the truck getting a call, and then going off with lights and sirens.

Set over this but he was operating the truck one day and realize that it was taking too long to provide water to the fire scene. He decided he needed to come up with some way to fix that. He worked on high comment the side on the nights and weekends.

Traders Exchange

Mtr Main engine 2 CAT B, generator 3 kw- 1 generator 75kw,bow thruster 1 HP 12 ton thrust, 64 ton bollard pull, accommodation 22 men, fire fighting equipment, communication and navigation equipment, helicopter hoisting area. GT , NT Fully certified, last drydock , next due Fuel oil 73, gallons, lube oil gallons, potable water gallons, ballast gallons.

Has new zincs, new point, full list of work is available.

Start studying 29 RBS. Learn vocabulary, terms, and more with flashcards, games, and other study tools.

And I have at least passing knowledge of hundreds more vacuums. At the time of writing, I counted 17 vacuums in my condo, and I might have forgotten a couple. I once took a suitcase filled with small vacuums from Boston to New York. For this particular update, I put in an additional 15 hours of research into about 50 new models, plus dozens of additional hours of using our favorite vacuums to clean my own home.

And other Wirecutter staff members have used them at home, as well. Justin Haver, vice president of GoVacuum.

Brush Hero on ‘Shark Tank’: A Look Inside the Spinning Brush the Powers With Your Garden Hose

The fleck SXT water softener features: Made using the highest end components and hand assembled. Experience the difference and see why we are the industry leader.

Small Town Terrors: Pilgrim’s Hook Walkthrough Use the crowbar on the sign to get a shark tooth (D). Move the 3 bricks to get the binoculars (E). Examine the boat; use the EMPTY GAS CAN and the LENGTH OF HOSE on the tank. Take the FULL GAS CAN (M).

I installed this last winter to replace the old corroded cold water supply valve when we replaced the hot water tank. Also has the Sharkbite supply lines. The HD guy explained how to do it and it took no time at all, He also said keep removal tool on line so you don’t lose, you can see it just above valve in pic I just recently checked the valve and no leaks all is still secure.

It was great not having to sold joints and it is a solid fit. Planning on buying more to install additional shutoff valves around house this winter as the builder who did our house in 80’s did bare minimum code meaning only a main supply cutoff, none for other zones. Did not leak and the best part is that I didn’t have to sweat copper pipes creating all those horrible solder fumes.

Last time I had to sweat copper pipes my wife and kids couldn’t take it so she ended up taking the kids out of the house for hours. Soldering in these circumstances is impossible, and the speed of mounting a valve like this can’t be beat with a compression fitting. One caution — debur the copper well, because you can’t scratch the o-ring inside. If you do, it won’t seal well and you’ll have to start all over again. What a solution — permanent, doesn’t cost all that much more than a regular brass valve, and installation is a snap.

This valve is made of superior quality.

Kubota Wet/Dry Vacuum 12 Gallons

I was thinking maybe 2 tanks up top on an inner tube type setup, but seems like there would be more potential for stuff to go wrong. Which is mainly why I wanted to just try out a hookah first. They make a variety of systems. Check them out at http: We can run down to sisters creek and you can try it out.

The 3/4 in. x 18 in. SharkBite Water Heater Connector allows you to easily connect your Hot and Cold-Water Supply lines to your Water Heater. After applying pipe thread tape to the MIP nipples on your water heater, thread the FIP end of the Water Heater connector onto the tank /5().

I finally found the water heater was loaded with the rubber and found the rubber liner in the sharkbite flex line was deteriorating. I called Sharkbite and they said they changed the liners and if I bought new lines manufactured after that they would have the new liners. That was late or early and now here it is and the lines have deteriorated again.

I don’t recommend these and will not be suckered into them again. After on line research I found it could be the black rubber liner in these connectors that was deteriorating. In deed that was the cause. I removed the hoses and cut them in half and the hot water hose was filled with black gunk. Also some in the cold water but not as bad. SharkBite claims it is caused by hard water and chlorine.

Since most of the US has hard water and chlorine it would seem few are safe from deterioration. I used 2 11” flex hoses and a in line ball valve on my new hot water tank install and it made what might have been a tough job very easy Date published: I had one of those nightmare weekends where I had an unplanned water heater installation.

Shark S4701 Series Owner’s Manual

Many of us do padlock the trailer hitch lever down so it can not be disconnected from the ball. This can also be a good thing to get used to doing as it is a reminder to not forget to snap the lever down onto the ball. But what about securing the hitch extension into the bumper’s receiver?

BISSELL is committed to donating up to $1,, each year to BPF, but is on track to far exceed that goal. BISSELL will donate up to $10 for each pet product purchased* to BPF to .

I recently went with a pair of Pressure Pro heaters for my project and they seem to be performing well. When choosing a commercial pressure washer, the one with hot water mechanism is recommended because it delivers better cleaning results. It softens oil and grease, which makes it especially effective when cleaning cars. Another good thing about a hot water pressure washer is that it reduces the amount of detergent and cleaning agents that are consumed.

Using only hot water will already be effective in the removal of tough stains and dirt. It results to not only cost savings, but it is also good for the environment. To add, using hot water in a commercial pressure washer also speeds up the drying time. More so, the working time is significantly lessened since it is tougher on dirt and will allow you to accomplish your task while exerting minimal effort.

Essential Factors to Consider As you try to narrow down the options that are available on the market, here are some of the most important things that should be taken into account: One of the first considerations is how the water is heated.

Vacuum cleaner

Marine Bed Liner interior Available in tan, light gray, charcoal, red, or white. Tachy when wet, and quiets the ride. Other colors available with notice. No wood or plastic here.

50m shark line with 50m bouy lines either end comes ready to use with 2 bouys 2 weights and 15 hooks all rolled up nice and tidy on a hose reel. Any queries call or text Burnie Area Burnie.

Silicone household sealant or plumbers tape Chalk Pina Colada mix Step 1: Get Pumped Up The fittings for the Coleman pump unit and the Super Soaker pack are very compatible with some simple modifications. The Coleman pump intake has a removable piece with threads on the inside. It can be inserted on the inside of the large orange valve gasket from the Super Soaker pack so the pump and pack can be screwed together.

But first, the inside of the Super Soaker gasket must be prepared. Unscrew the large orange gasket fitting and use pliers to break or cut away the plastic struts holding the central piece. With the Dremel tool grinder or sander attachment, smooth out the inside of the barrel. This should give the threaded part from the Coleman pump enough clearance so that you can fit the gasket over it, and screw it back onto the pump unit.

Now you can attach the pump directly to the Super Soaker pack. If the fittings are screwed in tightly enough, the seal should be nearly leakproof. We did a test run with water and the pressure from the pump was impressive. You should cut the vinyl tubing from the pump to about half its length, since it is more than long enough. Also, on the Super Soaker pack, there is a piece of vinyl tubing on the other end that is meant to hook up to the water gun.

Since this will not be used, you can cut the tubing off an inch or so away from the bag and fill it in with silicone caulk to plug it.

HyConn inventor Jeff Stroope on Shark Tank


Hi! Would you like find a partner for sex? It is easy! Click here, registration is free!